Do you have a plumbing problem at home? Fortunately, the vast majority of plumbing problems can be repaired quite easily, instead of calling a plumber and making him your new best friend. Often, all you need to finish the job is a rudimentary toolbox and willingness to learn. Some common problems found with plumbing include:
– Race Toilet
– Backed-up Toilet
– Noisy Hoses
One of the most common is the toilet being run. Usually, this problem can be solved simply by replacing a faulty valve or a defective ball assembly. Flapper is either staying upright or not sitting well. In order to solve this problem, you must first turn off the water at this toilet. Then remove the toilet tank lid. Take the flapper and take it to the hardware store to make sure you buy the right replacement. This is an easy solution and it will cost you around $ 5. In some cases, it will be necessary to clean the mineral deposits from the tank itself. Vinegar, boiling water and baking soda are usually the case, but be careful if you have a marble floor in your bathroom. Marble, slate and granite can be damaged by parasitic drops of an acid solution.
"Are you still going to a big party, go to the bathroom, flush the toilet and the water starts to come up?" This is the scariest moment the life of a human being, lose his head and start talking to the toilet. "No, please, do not do that to me!" "Jerry Seinfeld
The One Worst thing about clogging toilets is obstructing someone else's toilet.The most important thing to remember is that if you ride once and that the water rises dangerously, DO NOT RINSING again! Instead, you should quickly remove the tank lid and push the tank ball down to close the flush valve.
Plumbing You will say that most toilet blockages are caused by plastic items, sanitary products and toys.If the construction may be the result of an object dropped into the toilet, such as a toy or washcloth, then it is best to try to recover it rather than to force it further.Other hooves resulting from normal waste can be cleaned with the help of a diver or d & # 39; an endless screw
First try to use a piston to dislodge anything that might be trapped in the toilet bowl. If the bowl is full, put on gloves and draw water until the bowl is half full. If the bowl is empty, add water to fill it halfway. In order to avoid the possibility of splashing, drape a large towel over the bowl and under the toilet seat. Start by sealing the hole in the bowl with the plunger. Push slowly and back quickly. Start by doing this at a slow pace and then speeding up. If you see something stuck in the drain opening, you can use a stiff wire to bring it back into the bowl. If you dislodge the object, pour about a gallon of water into the bowl before rinsing. The water should drain to its normal level and stay there.
However, large hooves will probably require a closet auger. Make sure you have a toilet snake / auger, as a sink snake / auger will scrape the porcelein on your toilet. They are specially designed for the toilet, so that when you place the padded section at the bottom of the bowl and you push the handle down with a quick, hard motion, a piece of coiled metal will mend its way 4-5 feet into your toilet. The crank around the handle should free most clogs. If the water seems to be emptying properly, go ahead and try to pull the toilet.
From banging to pounding through acute squeaking, your water pipes produce a symphony of sounds that gives you the impression of living in a submarine. The squeak and crash that you hear probably result from an adjustment too loose or too tight when your pipes pass over or through a wooden frame. The trick to solving this problem is to identify the specific sounds, and to know from which valley the pipes, the pipes call.
Knocking – If not properly installed, water lines may lift a racket by striking floor joists. The pipes are usually / hopefully anchored with metal or plastic straps every 6 to 8 feet for horizontal strokes, or 8 to 10 feet for the vertical. Twist hoses usually mean loose hoses. All it takes to solve this problem is to add more straps to anchor the hose. Cushion the hose by wrapping it in a rubber blanket cut from an old inner tube, hose or foam pipe insulation. Wrap the rubber completely around the pipe and secure it to the joist with the help of a nailed metal pipe strap.
Squeak – Only your hot water pipes squeak. The sound occurs when the pipe expands in its strap causing friction. The problem is the opposite of a cooking hose but the solution is the same: a rubber cushion between the hose and the strap.
Water Hammer – Have you ever turned off a faucet or appliance, causing the water to "hammer" against the pipes? This is the most common of the inilets. Plumbing systems usually have air cushions, & # 39; short vertical sections of the hose designed to cushion the shock when the water is on or off. If there is no air cushion or if the air cushion is filled with water, you may hear a loud popping noise after cutting off the air. water or rinse. Turn off the water at the main shutoff valve. Open all your faucets to drain the entire system. Turn off the faucets and turn on the water again. This should fill your rooms with air.
Many things, including the infiltration of cracked pipes, a corroded water heater or a faucet or a Overflowing toilet can cause flooding. Whatever the cause, take immediate action to shut off the water. If necessary, contact a plumbing professional to identify and fix the problem. If there is stagnant water that needs to be pumped, you will need a sump pump to extract the water, or you can ask the plumber to do it. In case of flooding, pay particular attention to the possibility of danger from electrical wiring. Water and electricity are a dangerous combination. Never walk in stagnant water when there is contact with electrical outlets or wiring.